14 Dec
1999
14 Dec
'99
10:19 p.m.
Hi -
From arno(a)usn.nl Mon Dec 13 23:28:32 1999
The '94 is way cool! I'm amazed at the extensive menu-based boot ROM in
Yep - I have seen that on the 11/93 at my place. Nice. Having the
"toyclock" to get the date/time from is real good too.
this thing. At least the RA92's are quite a bit
more 'civilized' than the
RA82 on my uVAX which is more like a howling banshee..
Use less power and are more reliable (also larger capacity I believe)
otherwise I wouldn't have had the problem.. I
have an UC07 SCSI controller
I could use for a while (but it's QBUS) to hook up a tape drive.
As I was reminded a short time ago - don't put a Qbus board into a
Unibus machine (or the other way around) :-)
Any network connection will be OK.. I hope BSD has PPP
support? That
should give at least some rudimentary network connectivity (even if it's
just 9600)
SL/IP yes but 2.11 predates PPP and I am not sure there is room in
the kernel/networking for PPP (which is a much more complex protocol).
I've run SL/IP just fine - and if you have the (fairly) recent updates
to enable hardware flowcontrol you can run considerably faster than
9600 and not worry about dropped characters or truncated packets.
Or I could use 1 RA92 (with the problem you describe)
and use it to
run the install on the second drive? (partitioning that properly)
Ah, yes indeed! As long as the kernel's idea of the drive size
is less than what the actual disk image is then you should not have
any problems - i.e. if you put an RA60 sized image on an RA92 it
should work (at least well enough to configure the 2nd drive correctly).
Obviously the other way around would not work ;)
Guess my first search will be for either an UNIBUS
SCSI controller or
a TK50/TK70 controller as I still have some drives for those..
A TK70 controller will run a TK50 drive very nicely _and_ offer
the benefit of the buffer cache (which speeds things up greatly). I
do not know if there was a Unibus TK50 adaptor though.
An inexpensive TS05 would be a real nice thing to have about now ;)
Steve
Received: (from major@localhost)
by minnie.cs.adfa.edu.au (8.9.3/8.9.3) id IAA53230
for pups-liszt; Wed, 15 Dec 1999 08:56:14 +1100 (EST)
From Tim Shoppa <SHOPPA(a)trailing-edge.com> Wed
Dec 15 07:55:41 1999
Received: from timaxp.trailing-edge.com
(timaxp.trailing-edge.com [63.73.218.130])
by minnie.cs.adfa.edu.au (8.9.3/8.9.3) with SMTP id IAA53226
for <PUPS(a)MINNIE.CS.ADFA.EDU.AU>; Wed, 15 Dec 1999 08:56:05 +1100 (EST)
Received: by timaxp.trailing-edge.com; Tue, 14 Dec 1999 16:55:41 -0500
Date: Tue, 14 Dec 1999 16:55:41 -0500
From: Tim Shoppa <SHOPPA(a)trailing-edge.com>
To: sms(a)moe.2bsd.com
CC: PUPS(a)minnie.cs.adfa.edu.au
Message-Id: <991214165541.246000ac(a)trailing-edge.com>
Subject: Re: Installing UNIX on an 11/94
Sender: owner-pups(a)minnie.cs.adfa.edu.au
Precedence: bulk
> From arno(a)usn.nl Mon Dec 13 23:28:32 1999
> The '94 is way cool! I'm amazed at the extensive menu-based boot ROM in
Yep - I have seen that on the 11/93 at my place.
Nice. Having the
"toyclock" to get the date/time from is real good too.
As long as you've updated to the Y2K-compliant KDJ11-E firmware, that is.
The "old" firmware will do fine up until the end of 28-Feb-2000, when it
will promptly wrap back around to 1990. You can use 2.11BSD 'toyset'
(or the RSX-11 or RT-11 equivalent) to set the TOY clock after that date,
but at power on it'll reset back to 1990.
See the discussions in vmsnet.pdp-11 earlier this year for the ordering
code and cost (I think it's around $25.00) for the new 11/93 and 11/94
firmware.
--
Tim Shoppa Email: shoppa(a)trailing-edge.com
Trailing Edge Technology WWW: http://www.trailing-edge.com/
7328 Bradley Blvd Voice: 301-767-5917
Bethesda, MD, USA 20817 Fax: 301-767-5927